Exhaust gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe

2 exhaust bushes required per bike

 More than 5 in stock

 91113826 GU91113826 91 11 38 26
 9111 3826 9111.3826 91.11.38.26

Heavy duty stainless steel exhaust silencer clamp replaces Guzzi ref. 29123450, 03123400

 More than 5 in stock

 14123400 GU14123400 14 12 34 00
 1412 3400 1412.3400 14.12.34.00

Exhaust gasket for standard downpipes, less expensive alternative to factory part

Copper gasket

 3 in stock

 852090 MG852090

Also fits Aprilia RSV4, Aprilia Tuono V4, Aprilia RS660

Stainless steel exhaust header pipe and balance box exhaust clamp

See EXA36901 for alternative part

 2 in stock

14126900-z 14126900 GU14126900 14 12 69 00
 1412 6900 1412.6900 14.12.69.00

Pair of short reverse cone stainless steel performance silencers from Mistral, the reverse cone design compliments the classic styling of the V7 models. Supplied with removable DB killer these are a more durable, stylish, lighter and better sounding than the original silencers.
No remap required

Also available in polished finish

Euro 4 compliant

All Mistral exhausts are hand made in Mandello using high quality components, Mistral develop exhausts that get the best performance from your Moto Guzzi.
Supplied with silencer clamps and certificate of homologation, reuse your existing silencer brackets with these silencers. Note that the optional Guzzi factory centre stand requires stop bracket FRA33380 to prevent the stand touching the underside of the silencer.

Silencer gaskets now included with these silencers

Release the music in your Guzzi!
See this video to hear this silencer

 1 in stock

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 1 in stock

Exhaust stud, see ENA96043 for less expensive alternative

See ENA31880 for stud nut

 This part is available by special order, request a quote

 96506042 GU96506042 96 50 60 42
 9650 6042 9650.6042 96.50.60.42

Collet for exhaust manifold, two required per cylinder

 This part is due back in stock soon, call 01484 841395 to reserve yours

19025460-z 19025460 GU19025460 19 02 54 60
 1902 5460 1902.5460 19.02.54.60

Stainless steel crossover pipe, sounds much better than the original!

Handmade to order in Italy
Includes threaded hole for Lambda sensor. Improves performance and access to your oil drain plug. Supplied with stainless steel exhaust clamps

 This part is available by special order, request a quote

Pair of satin finish stainless steel reverse cone performance silencers from Mistral, the reverse cone design compliments the classic styling of the V7 models. Supplied with removable DB killer these are a more durable, stylish, lighter and better sounding than the original silencers.

All Mistral exhausts are hand made in Mandello using high quality components, Mistral develop exhausts that get the best performance from your Moto Guzzi.
Supplied with silencer clamps and certificate of homologation, reuse your existing silencer brackets with these silencers. Note that the optional Guzzi factory centre stand is not compatible with these silencers (unless you make up a centre stand stop bracket to prevent the stand touching the underside of the silencer). Silencer gaskets now included with these silencers
No remap required

Release the music in your Guzzi!

 This part is available by special order, request a quote